Tiny Bubbles - Engraving Etc. Forum

<body> <h1>Full Version: <a href="https://www.engravingetc.org:443/archive/index.php?webtag=EE&msg=19.4">Tiny Bubbles</a></h1><a name="a19_4"></a><p><b>From: BettyW</b> [<a href="lmessages.php?webtag=EE&msg=19.4">#4</a>]<br /> 28 Jul 2004<br /><b>To: Stunt Engraver (DGL)</b> [<a href="lmessages.php?webtag=EE&msg=19.3">#3</a>] 28 Jul 2004</p> I am working right below a florescent light. Maybe that is part of it. Will give the subdue light a try.<br /> <hr /><a name="a19_5"></a><p><b>From: Engravin' Dave (DATAKES)</b> [<a href="lmessages.php?webtag=EE&msg=19.5">#5</a>]<br /> 28 Jul 2004<br /><b>To: BettyW</b> [<a href="lmessages.php?webtag=EE&msg=19.4">#4</a>] 28 Jul 2004</p> <p>Betty,</p> <p>If your flourescent light fixture(s) end up being the problem, get a roll of clear UV blocking film at your local Lowe's, Home Depot, etc. Open the cover on your fixture, completely cover the plastic lens with the film, then close the door.</p> <p>I used this method of screening UV rays in the room I develop my film for sandcarving. I have never had a problem with overdeveloped film.</p> <p>Of course, if your flourescent fixtures are not the enclosed type, you may be out of luck with this option. You could have one of your fixtures put on a seperate switch and have the bulbs in that fixture changed to yellow light.</p> <hr /><a name="a19_6"></a><p><b>From: BettyW</b> [<a href="lmessages.php?webtag=EE&msg=19.6">#6</a>]<br /> 28 Jul 2004<br /><b>To: Engravin' Dave (DATAKES)</b> [<a href="lmessages.php?webtag=EE&msg=19.5">#5</a>] 28 Jul 2004</p> <p>That is a really good idea. Going to give this a try too. thanks!</p> <p> </p> <hr /><a name="a19_7"></a><p><b>From: Zonas</b> [<a href="lmessages.php?webtag=EE&msg=19.7">#7</a>]<br /> 3 Aug 2004<br /><b>To: Stunt Engraver (DGL)</b> [<a href="lmessages.php?webtag=EE&msg=19.1">#1</a>] 3 Aug 2004</p> <p>David, I know you have also mentioned doming your name tags on the sub forum. Could you post a picture? Are you using frames/holders with your name tags? </p> <p>Zona<br /> Zona's Engraved Creations</p><hr /><a name="a19_8"></a><p><b>From: Stunt Engraver (DGL)</b> [<a href="lmessages.php?webtag=EE&msg=19.8">#8</a>]<br /> 3 Aug 2004<br /><b>To: Zonas</b> [<a href="lmessages.php?webtag=EE&msg=19.7">#7</a>] 3 Aug 2004</p> <p>Zona,</p> <p>I use some with frames, others without.</p> <p>I'll put something in the "Show & Tell Gallery." You'll have to be a bit patient. Still handling time-sensitive tasks at the moment.</p> <p>David "The Stunt Engraver" Lavaneri<br /> DGL Engraving<br /> Port Hueneme, CA</p><hr /><p align="center">Show messages: <a href="lmessages.php?webtag=EE&msg=19.1">All</a>  <a href="lmessages.php?webtag=EE&msg=19.1">1-3</a>  4-8</p> <h4><a href="lthread_list.php?webtag=EE">Back to thread list</a> | <a href="llogout.php?webtag=EE">Login</a></h4> <h6>© 2026 <a href="http://www.beehiveforum.net/" target="_blank">Project Beehive Forum</a></h6> </body>