Full Version: Just curious
From: Pete (AWARDMASTERS) [#9]
29 Mar 2005
To: LaZerDude (C_BURKE) [#8] 29 Mar 2005
From: precisionlaser [#10]
29 Mar 2005
To: LaZerDude (C_BURKE) [#8] 29 Mar 2005
Chuck,
Don't feel bad. You know the old adage about the "sausage factory"? The one where the pig goes in and sausage comes out, but you don't want to know what happens in the middle? I've taken on jobs that ultimately turned out fine, but where, as the English would say politely, I made a "hash of it" in the middle. Most of my clients never knew (or were too polite to acknowledge that they knew) the panic and chaos of the middle part. I lost money on each of those jobs, no doubt, but they were "school fees" as Rodney calls them. I gained experience that's paid off time and again.
Another of my favorite sayings that applies to this is "bite off more than you can chew...and then chew it, darn it!" (PG version). I don't know how else you learn except by taking risks, although it does contribute to a lighter shade (and sometimes less) of hair!
Mark
From: LaZerDude (C_BURKE) [#11]
29 Mar 2005
To: precisionlaser [#10] 29 Mar 2005
Mark,
Thank you for your encouragement......one problem though.
We met in Vegas. You saw my hair. If I lose much more hair, I'm going to look like Joe Hayes. ( Insert laugh here)
From: precisionlaser [#12]
29 Mar 2005
To: LaZerDude (C_BURKE) [#11] 29 Mar 2005
Now, I met Joe and Toni, and while Toni was clearly the "looker" of the two, Joe was (and I presume still is...) very distinguished looking! ;-))
Mark
From: JHayes55 [#13]
30 Mar 2005
To: LaZerDude (C_BURKE) [#11] 30 Mar 2005
From: JHayes55 [#14]
30 Mar 2005
To: precisionlaser [#12] 31 Mar 2005
From: LaZerDude (C_BURKE) [#15]
30 Mar 2005
To: JHayes55 [#13] 31 Mar 2005
Now did I say anything disparaging? I mean all I said was that I would look like you :) (Insert laugh here)
From: JHayes55 [#16]
31 Mar 2005
To: LaZerDude (C_BURKE) [#15] 31 Mar 2005
All I can say is that when it come out just accept it and for goodness
sake never start that comb-over style.
Nothing worse than a man with 14" hair all from one side just above the
ear combed from side to side - or back to front. Geesh!!
:)
From: Harvey only (HARVEY-ONLY) [#17]
31 Mar 2005
To: JHayes55 [#16] 1 Apr 2005
As long as you have some left in the front, a ponytail covers a lot and is not as obvious. (Snicker, snicker.)
From: JHayes55 [#18]
1 Apr 2005
To: Harvey only (HARVEY-ONLY) [#17] 1 Apr 2005
Harvey
So true. If that is the case then Lazerdud need to get started very fast.
Ok Chuck - time is wasteing - get those 2 or 3 up front to work on that
pony tail.
From: LaZerDude (C_BURKE) [#19]
1 Apr 2005
To: JHayes55 [#18] 2 Apr 2005
From: UCONN Dave & Lynn too (DANDL48) [#20]
2 Apr 2005
To: LaZerDude (C_BURKE) [#19] 2 Apr 2005
Chuck,
Ever get the laser resist and how did it work?
Dave
From: LaZerDude (C_BURKE) [#21]
2 Apr 2005
To: UCONN Dave & Lynn too (DANDL48) [#20] 2 Apr 2005
Dave,
I did get the laser resist. I have just not developed the patience for it yet. I thought I had it working, but then I realized that in my quest to get it smooth, I stretched it to hard and far, so when I lasered it, it stretched even more. Interesting effect but not good for my customer.
Sooooooo we have sprayed all the glasses with Plasti Dip and it seems to work fine. Once I'm done with my key fob project, I'll be back to the glasses. If I remember, I'll send you a picture of one.
Hi to Lynn
From: UCONN Dave & Lynn too (DANDL48) [#22]
2 Apr 2005
To: LaZerDude (C_BURKE) [#21] 2 Apr 2005
Chuck,
What's the dementions of the artwork?
Dave
From: LaZerDude (C_BURKE) [#23]
2 Apr 2005
To: UCONN Dave & Lynn too (DANDL48) [#22] 2 Apr 2005
Dave,
Top to bottom is 1.25". side to side is 1".
The challenge is that the font size gets smaller near the bottom and I cannot get a clean blast for the font. The logo comes out great. I don't know if it would help if I could get the mask to lay flat.....
From: UCONN Dave & Lynn too (DANDL48) [#24]
2 Apr 2005
To: LaZerDude (C_BURKE) [#23] 2 Apr 2005
I see.
You do have a rotary attachment for the laser?
Dave
Message 1040.25 was deleted
From: Engravin' Dave (DATAKES) [#26]
2 Apr 2005
To: LaZerDude (C_BURKE) [#23] 2 Apr 2005
Chuck,
The logo you sent me for the glasses had very small, fine letters for the last two lines. Is your customer flexible enough to allow you to enlarge the image at all, or is the glass restricting you to this dimension?
I bought my new inkjet yesterday and will be doing a RapidMask test for you (and me) this afternoon. I will post the results, with or without success. I will also report the PIR Factor, if I feel it is warranted. PIR Factor = Pain In Rear.
From: UCONN Dave & Lynn too (DANDL48) [#27]
2 Apr 2005
To: Engravin' Dave (DATAKES) [#26] 2 Apr 2005
David,
What kind of an inkjet did you get? Pigmented Inks?
Dave
From: Engravin' Dave (DATAKES) [#28]
2 Apr 2005
To: UCONN Dave & Lynn too (DANDL48) [#27] 2 Apr 2005
Dave,
I ended up getting an Epson C86. At the store I was able to print a sample image on AccuArt 2 and it was very opaque. I am still not sold on RapidMask resist yet, so I wasn't in the spirit to spend much money on an inkjet.