Full Version: Industrial Etching
From: LaZerDude (C_BURKE) [#14]
3 May 2005
To: Rodney Gold (RODNEY_GOLD) [#11] 3 May 2005
Rodney,
Do you have or know of an American supplier of that product?
From: LaZerDude (C_BURKE) [#15]
3 May 2005
To: Geezer (ERNIE) [#10] 4 May 2005
Ernie,
Thank you for the tid bit on onsite blasting.....however, what about the "fallout" or sand that is left after and during the etch. Clean up would be a bear wouldn't it?
From: LaZerDude (C_BURKE) [#16]
3 May 2005
To: Ken D. (KDEVORY) [#8] 4 May 2005
Ken, you said,
I know you were joking, but its important people understand there is a big difference between the compressors we might have and the ones used for scuba tanks. (Would you put food in your mouth after it was in your compressor?)
And of course the answer is no, but I have eaten a banana under 40 feet of water.... :)
From: Rodney Gold (RODNEY_GOLD) [#17]
3 May 2005
To: LaZerDude (C_BURKE) [#14] 3 May 2005
Hiya Chuck
Just about any small hole in the wall vinyl or signmaking supplier should have it , it's used extensively. Called Sandblast vinyl or window etch vinyl. there are different grades from cheap and nasty to mondo expensive cast polymeric (vinyl that will be able to be streched over a compound curve)
3m , avery , grafitak etc all make versions of it.
From: Engravin' Dave (DATAKES) [#18]
4 May 2005
To: LaZerDude (C_BURKE) [#15] 4 May 2005
Chuck,
On-site blasting does have its own special requirements because of all the dust that is created.
I have seen blasting done in an office environment where they built a tent enclosure to contain most of the dust.
If you are serious about this, I would recommend a system from Glastar made specifically for dust-free, on-site sandblasting. The blaster, pictured in the attachment, uses a high volume vacuum return to recapture the dust and abrasive and to recycle the usable abrasive through the blaster continuously.
The blasting section of the Glastar unit looks like a brush attachment that you would find on a vacuum. The abrasive media is released and reclaimed within the brush. I would argue that it probably is not 100% dust-free.
This Glastar blaster is a siphon system, so it requires a substantial amount of air to operate continuously for long periods of time. If your existing compressor is not adequate, or if it is not portable, renting a larger compressor could be a viable, low-cost option for you to get into on-site blasting.
Many people doing on-site blasting use 2 hp, 110v compressors even though these compressors do not provide enough air to blast for long periods of time. They simply modify their blasting technique to alternate short periods of cutting out the resist with short periods of blasting, instead of doing all the cutting first and then all of the blasting. Some people use two 2 hp compressors to provide a longer period of blasting time before running out of air.
Some of the above information has been taken verbatim from the Glastar website.
EDITED: 7 Jun 2010 by DATAKES
From: Geezer (ERNIE) [#19]
4 May 2005
To: LaZerDude (C_BURKE) [#15] 4 May 2005
Cleanup is very minimal. About what you'd have from eating a dozen soda crackers. That's the beauty of the siphon blaster.
The construction of a siphon blaster is such that it projects the blast media and also sucks it and the glass shards up at the same time.
You should probably get the video that Norm Dobbins has showing the actual use of a siphon blaster to see just what happens.
Be advised though that the siphon blaster will not allow deep penetration or stage blasting of the glass. However, since most on site work is with tempered glass you won't be trying for depth.
Ernie