Full Version: Roland Impact MPX70
From: sprinter [#7]
22 May 2006
To: ALL
From: Harvey only (HARVEY-ONLY) [#8]
22 May 2006
To: sprinter [#7] 22 May 2006
Including proper photo setup and engraving for the best results, a 1x2 dog tag takes about 30-45 minutes. The actual engraving on the tag is 20-30 minutes. That is for an MPX-50. You have to run at about 1/2 speed from the default to get a really good image. Image prep is critical to a good result. You need to develop an eye for what is best, certainly not the best looking picture. The places that do it for a living, (carts in a mall), usually have four machines. The MPX-50 is a bummer in that each machine needs its own IEEE parallel port. The machine has almost no memory and ties up the port during the whole operation.
Never call it a Metaza publicly, it is Impact Engraving. Do not give your business away by advertising the sources of the equipment.
From: sprinter [#9]
22 May 2006
To: Harvey only (HARVEY-ONLY) [#8] 22 May 2006
From: Dee (DEENA-ONLY) [#10]
23 May 2006
To: buck [#6] Unread
Buck,
Our least expensive impact is 24.95 done on a nickle plated dog tag. They go up to $50.00 or more if they have jewels around them and then add an "upscale" chain. The kids have no problem with those prices as they are often thought about as an article of clothing like a watch.
We sell an average of 10 a week and yes 99% are to kids and young adults.
Dee
From: LipChip [#11]
23 May 2006
To: buck [#1] Unread
Hello Buck,
Many of the forum replies to your question have been "right on". Having worked with the Metaza products, and being the lead technology source for glazing/doming these products with capabilities approved by Roland and Dr. Metaza himself... see our website (UV Glazing), once you find your market the products are very successful and was a top notch winner and the recent PMA Show in Orlando. There is also a "MetazaMasters" Yahoo Group that you might want to check into to get the opinions of users of the technology.
Best of luck.
Dave / LipChip
From: varn (VARNCO) [#12]
23 May 2006
To: buck [#1] Unread
I had an old MPX50, and didn't really care for it that much.
To really "see" the images, you had to hold the image just right to get the glimmer of light to reflect off it.
You also can not use it on any item that has a lip to it, where the engraving area is lower than an outer edge.
It did seem to take a long time to engrave, but I've heard the new ones are much faster and I believe a bit higher resolution.
YMMV
From: Harvey only (HARVEY-ONLY) [#13]
23 May 2006
To: varn (VARNCO) [#12] 23 May 2006
The only problem with higher resolution, is that you still have to tilt it just right to see the image.
There are one or two tricks that I keep to myself that makes it look right at almost any angle. When you get it to the old 'just right' angle it looks crappy though.
From: Stunt Engraver (DGL) [#14]
23 May 2006
To: Harvey only (HARVEY-ONLY) [#13] 23 May 2006
Some people are epoxy doming the output, which magnifies the image.
Still need to hold it at the appropriate angle for viewing though.
From: Harvey only (HARVEY-ONLY) [#15]
23 May 2006
To: Stunt Engraver (DGL) [#14] 23 May 2006
From: LipChip [#16]
23 May 2006
To: Harvey only (HARVEY-ONLY) [#15] 12 Jun 2006