Full Version: cannot blast thru rapid mask 3000
From: Engravin' Dave (DATAKES) [#13]
15 Aug 2006
To: Ozzy Fox (CLIVEGARAWAY) [#12] 16 Aug 2006
Peter,
I will second what Clive said. Use a white clipboard and warm water, not hot. There is an acquired skill in timing the washout process. There is a fine line between too washed out and not washed out enough. I'm glad your making progress. Your customers will be thrilled.
I'm still curious if you have decided what you are going to use for printing your images. We could share some guidance in this area as well.
I personally have had years of success using a laser printer and vellum. This is a much cheaper process than inkjet and the more expensive, specialized paper you have to use to get an opaque image.
EDITED: 15 Aug 2006 by DATAKES
From: Ozzy Fox (CLIVEGARAWAY) [#14]
16 Aug 2006
To: ALL
Like Dave I also use a basic laser printer and vellum, if the image is not dark enough or you have very fine lines then I use a spray can of Krystal cote which darkens the image and helps the process. I also found not to trust the letralite timer I use a second hand on a watch and for between 19-21 seconds,and I mean BETWEEN 19&21,
(maybe 2 seconds more on 5 mm resist.).
I have not found the fluro tubes or UV to cause me any major issues, I cutoff what I need and put it away, expose the job, washout, let dry, stick on and blast, usually 15-30 mins depending on drying time.
regards Clive.
From: RALLYGUY (RALLYGUY1) [#15]
21 Aug 2006
To: Peter [#5] Unread
A UV safe environment doesnt have to be dark. They sell yellow light covers that block uv from fluorescent lights. We use these in our screen exposure room (similar process and chemistry as resist materials).
This may be the ticket, if you're having over exposure issues.
One way to test is to take a coin and a fresh unexposed section of material. Immidiately place the coin on the sheet and leave out for an estimated amount of time that you would be working with the materials. Apply to product and try to blast the material. If you are able to blast the coin shape properly, it is likely that you are exposing the material too much while processing, and need either shorter processing times or better UV control.
If it acts the same, you are having other issues...one of which could be bad material, or as someone else mentioned, you may not be removing the liner properly. This liner if left intact would protect the resist from blasting, and could theoreticaly act the same.
Hope this helps......
From: RALLYGUY (RALLYGUY1) [#16]
21 Aug 2006
To: RALLYGUY (RALLYGUY1) [#15] 21 Aug 2006
From: UCONN Dave & Lynn too (DANDL48) [#17]
22 Aug 2006
To: RALLYGUY (RALLYGUY1) [#15] 22 Aug 2006
Where do you get the UV covers?
Thanks,
Dave
From: RALLYGUY (RALLYGUY1) [#18]
22 Aug 2006
To: UCONN Dave & Lynn too (DANDL48) [#17] 22 Aug 2006
I believe Midwest Sign and Screen has them....Any Screen printing supply company should have something like this.
http://www.midwestsignandscreen.com/index.html
Looks like they have a location in your region...... :)
EDITED: 22 Aug 2006 by RALLYGUY1
From: Engravin' Dave (DATAKES) [#19]
22 Aug 2006
To: UCONN Dave & Lynn too (DANDL48) [#17] 22 Aug 2006
Dave,
If you light fixtures with lenses you can get UV blocking film at any hardware store and cut it to cover the lens. It is usually with the other tinting films.
After cutting to size, just open the light fixture set the film in place, then close the fixture. You are good to go.
From: RALLYGUY (RALLYGUY1) [#20]
22 Aug 2006
To: Engravin' Dave (DATAKES) [#19] 22 Aug 2006
From: UCONN Dave & Lynn too (DANDL48) [#21]
22 Aug 2006
To: RALLYGUY (RALLYGUY1) [#18] 22 Aug 2006
Thank you both!!
Dave
Show messages: 1-12 13-21