Full Version: Shanks Alot!

From: Stunt Engraver (DGL) [#1]
2 Jan 2007
To: ALL

Did you see Rodney's (inadvertent?) pun in the cutter grinder thread?

Somehow, I knew he'd have an "angle."

From: MIKEY (JADEPUTTERS) [#2]
2 Jan 2007
To: Stunt Engraver (DGL) [#1] 2 Jan 2007

and did you think he was a cut above any puns?

From: Harvey only (HARVEY-ONLY) [#3]
2 Jan 2007
To: MIKEY (JADEPUTTERS) [#2] 3 Jan 2007

I guess he just 'tipped' his hand.

Heard he needed a new truck, but instead he 'car buyed'.

When he imports materials he also has to use the right clearance angles.

From: Dave Jones (DAVERJ) [#4]
2 Jan 2007
To: Harvey only (HARVEY-ONLY) [#3] 2 Jan 2007

He's a 'sharp' guy. A real 'diamond' in the rough.

From: UncleSteve [#5]
2 Jan 2007
To: Dave Jones (DAVERJ) [#4] 3 Jan 2007

Should have known you all would start dragging this out again! >.<

You will all end up in your Grav o' plying your PUNishment on the rest of the world! :O)

From: Stunt Engraver (DGL) [#6]
2 Jan 2007
To: ALL

Hey!

I just "collet" as I see 'em. :-)

From: Dee (DEENA-ONLY) [#7]
3 Jan 2007
To: Harvey only (HARVEY-ONLY) [#3] 3 Jan 2007

I think y'all need to "burnish" this thread.

Dee

From: Stunt Engraver (DGL) [#8]
3 Jan 2007
To: Dee (DEENA-ONLY) [#7] 3 Jan 2007

Leave it to Dee to give us the "shaft."

From: Dave Jones (DAVERJ) [#9]
3 Jan 2007
To: Stunt Engraver (DGL) [#8] 3 Jan 2007

That's because she's by the sea on the east and you're by the sea on the west. And there's a lot of distance between the "sea and sea".

From: UncleSteve [#10]
3 Jan 2007
To: Dave Jones (DAVERJ) [#9] 3 Jan 2007

Have you gauged the depth of that statement? Just right to "cap" off the thread.

From: Dave Jones (DAVERJ) [#11]
3 Jan 2007
To: UncleSteve [#10] 3 Jan 2007

Whenever I come into this thread I feel like I'm on the 'nosecone' of a rocket ready to take off.

From: Stunt Engraver (DGL) [#12]
3 Jan 2007
To: ALL

You guys are forcing me to "grind" out some of my worst puns.

And that's saying a lot. :-)

From: LaZerDude (C_BURKE) [#13]
3 Jan 2007
To: ALL

Could we "collet" quits "andjust table" this?

From: Harvey only (HARVEY-ONLY) [#14]
3 Jan 2007
To: LaZerDude (C_BURKE) [#13] 3 Jan 2007

Although I like to be on the cutting edge, this thread is becoming quite a grind.

From: Stunt Engraver (DGL) [#15]
3 Jan 2007
To: Harvey only (HARVEY-ONLY) [#14] 3 Jan 2007

Harvey,

That goes without saying. You don't "halve" to say it out loud.

Full Version: Shanks Alot!

Back to thread list | Login

© 2024 Project Beehive Forum