Full Version: Mickey Mouse Job (w/photos)
From: UncleSteve [#4]
5 Mar 2007
To: Stunt Engraver (DGL) [#3] 5 Mar 2007
Oh, goody! Today I am a moderator!!!!! :-&
From: Harvey only (HARVEY-ONLY) [#5]
5 Mar 2007
To: UncleSteve [#4] 5 Mar 2007
From: UncleSteve [#6]
5 Mar 2007
To: Harvey only (HARVEY-ONLY) [#5] 5 Mar 2007
From: Mike (MIKEN) [#7]
5 Mar 2007
To: Stunt Engraver (DGL) [#6] 6 Mar 2007
Nice work.
You've convinced me!
I have to sell this machine. I could never do that kind of work.
From: geebeau [#8]
5 Mar 2007
To: Stunt Engraver (DGL) [#1] 6 Mar 2007
How cool is that!!!!!!!
Steve
From: UncleSteve [#9]
5 Mar 2007
To: Stunt Engraver (DGL) [#1] 6 Mar 2007
From now on, I will send all my stunts to you foro engraving...
Seriously, a beautiful job on a tough CPM*... :D
*Customer provided material
From: Stunt Engraver (DGL) [#10]
6 Mar 2007
To: Mike (MIKEN) [#7] 6 Mar 2007
That's one of the easier jobs. Not much different than engraving a 2" brass disc.
The difference is, not too many people will pay $25 for the same amount of engraving on a brass disc. :-)
It's the "fear factor" that makes people shy away from these types of jobs, not the level of difficulty.
I'll have to engrave a large silverplated tea urn this week. That will be much more difficult.
From: Stunt Engraver (DGL) [#11]
6 Mar 2007
To: geebeau [#8] 6 Mar 2007
Steve,
It's much cooler, after the proof-reading is over and finding everything was spelled correctly. :P
EDITED: 6 Mar 2007 by DGL
From: Doc (GREAT_ATLANTIC) [#12]
6 Mar 2007
To: Stunt Engraver (DGL) [#1] 6 Mar 2007
From: Stunt Engraver (DGL) [#13]
6 Mar 2007
To: Doc (GREAT_ATLANTIC) [#12] 6 Mar 2007
Thank you Jim.
I have an extra-long spindle on that machine, (would have also worked with a standard diamond spindle) so I didn't have to lower it as much as possible, although I did have to keep the highest point of the watch away from the upper portion of the spindle housing.
EDITED: 6 Mar 2007 by DGL
From: gt350ed [#14]
6 Mar 2007
To: Stunt Engraver (DGL) [#1] 6 Mar 2007
From: Dave Jones (DAVERJ) [#15]
6 Mar 2007
To: gt350ed [#14] 6 Mar 2007
From: gt350ed [#16]
6 Mar 2007
To: Dave Jones (DAVERJ) [#15] 6 Mar 2007
This won't be a problem. David just did not open the bezel cover far enough. I'm thinking 180 degrees...so everything lays flat. :O)
From: Doc (GREAT_ATLANTIC) [#17]
6 Mar 2007
To: gt350ed [#16] 6 Mar 2007
Would this require the hammer jig?
From: gt350ed [#18]
6 Mar 2007
To: Doc (GREAT_ATLANTIC) [#17] 6 Mar 2007
From: Engravin' Dave (DATAKES) [#19]
6 Mar 2007
To: Stunt Engraver (DGL) [#1] 6 Mar 2007
David,
I've never thought about engraving at a slight angle to gain better access to limited engraving areas. I learned something new today.
A have a big question I'd love to have answered. How does one remove a pocket watch cover? It can't be that complicated.
I've Googled the internet for information pertaining to the removal pocket watch lids and covers and have come up empty.
You could still charge the $25 because of the extra dis-assembly and re-assembly required, but it would be less risky.
From: Stunt Engraver (DGL) [#20]
6 Mar 2007
To: Engravin' Dave (DATAKES) [#19] 6 Mar 2007
I've never tried to remove the cover, mainly because there's a small spring to deal with.
I can imagine the spring shooting across the room, never to be seen again. >.<
Sometimes the pin in the hinge can be tapped through the opening, but they're often pounded flat or crimped somehow, to make the task more difficult than it would appear.
Probably quite easy for someone who works with watches and has the proper tools.
Timepieces are another lucrative area, where many engravers fear to tread.
BTW - The $25 was charged to a trophy shop client, who will probably resell the engraving for $50.