Full Version: Corporate Binders

From: LaZerDude (C_BURKE) [#1]
 19 Apr 2007
To: ALL

I have a CPA, that would give me all of their corporate seal, rubber stamp business if I could provide them with corporate binders..... ( three ring binder with fancy text on it)

I would need the blank binder and then a way to imprint it. Hot stamp won't work because the inside of the binder would already be in place so it could not lay flat.

I'm open to suggestions.

Thanks


From: Larry B (PALMETTO) [#2]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#1] 19 Apr 2007

Cut a mask in the laser and spray paint it or something like that. Not very many are their? What is the binder made of? Just one like you buy at Office Depot or the like?

From: LaZerDude (C_BURKE) [#3]
 19 Apr 2007
To: Larry B (PALMETTO) [#2] 19 Apr 2007

Larry,

Yes they are you basic 3 ring binder with a textured cover much like you would find on a photo album, not the vinyl cover typical of school binders. It also has a "box" the binder slips into.

I had actually thought of using laser thins....but your way might last longer.


As to how many, they will come in on or two at a time on an indefinite basis.....

Thanks


From: Larry B (PALMETTO) [#4]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#3] 19 Apr 2007

Yes, not enough to silk screen, oh, I guess you could if you already had the set up, but for ones and twos I would try and figure out something that would be fast, but would look good too and last. Those binders are not handled a lot after the client gets them, I don't think.

From: LaZerDude (C_BURKE) [#5]
 19 Apr 2007
To: Larry B (PALMETTO) [#4] 19 Apr 2007

quote:
Those binders are not handled a lot after the client gets them, I don't think.


I have touched my corporate binder 6 times at the most, in the 20 years I have been incorporated.


Now I just have to find a source for them....Sage, here I come

From: Larry B (PALMETTO) [#6]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#5] 19 Apr 2007

(Last time I saw mine I gave it to the attorney)

How about Rub n Buff to decorate the binder? I never have used the stuff, but it says it will stick to any dry surface. Cut a mask and Rub n Buff. Might work. Comes is a good selection of colors too I think.


From: Stunt Engraver (DGL) [#7]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#1] 19 Apr 2007

Chuck,

How about vinyl graphics for the cover?

From: LaZerDude (C_BURKE) [#8]
 19 Apr 2007
To: Stunt Engraver (DGL) [#7] 19 Apr 2007

quote:
How about vinyl graphics for the cover?


Dave, thanks..

The challenge is they want it on the spline.....but maybe I can explore that......I'd like to figure this out...this is one of those "niche" markets everyone keeps talking about....and there are LOTS of CPA's on the island.

thanks

From: Stunt Engraver (DGL) [#9]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#8] 19 Apr 2007

Vinyl is very flexible and if the adhesion is good, I think it would work.

From: LaZerDude (C_BURKE) [#10]
 19 Apr 2007
To: Stunt Engraver (DGL) [#9] 19 Apr 2007

How am I going to cut it? I'd have to have a sign company do it....

From: Stunt Engraver (DGL) [#11]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#10] 19 Apr 2007

Exactly!

A sign shop should be able to provide you with the pre-weeded vinyl, on application paper.

Create a hinge with a piece of masking tape, remove the protective backing, squeegie onto the binder and remove the top masking.

So easy, even I can do it and I have. :-)

From: LaZerDude (C_BURKE) [#12]
 19 Apr 2007
To: Stunt Engraver (DGL) [#11] 19 Apr 2007

Ok. Now I just need to find a source for the binders......

From: Stunt Engraver (DGL) [#13]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#12] 19 Apr 2007

Chuck,

My reading comprehension is shot. I thought you already had the binders.

From: Bill (ALBILLBERT2000) [#14]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#12] 19 Apr 2007

Hey Chuck.. first call me in the morning. at 215-887-8982 in addition to Engraving signs and rubber stamps.. were an office supply store.. we use a couple of companies for doing the corporate seal kits... to give you an example.. not only do you need the binder.. but you need the corporate min pages.. the assignment sheets for stocks.. need to be able to print stocks ... comon or par value.. have them numbered etc... one company in Sterling out of canada.. the does the entire thing for cheap.. cheap.... did I say cheap.. you call them.. and less than a week.. its in.. another is Carolina marking systems.. and I am sure there are others... We make corporate seals using our laser and mech engraver.. but for the entire package.. it is simpler to farm it out.. unless this lawyer is very big.. and giving you more than a few a month.. I would send it out.. if you would like to talk more.. call me

 

or use flex brass.. from romark

EDITED: 20 Apr 2007 by ALBILLBERT2000


From: LaZerDude (C_BURKE) [#15]
 19 Apr 2007
To: Stunt Engraver (DGL) [#13] 19 Apr 2007

No. That would be toooooo easy....

From: LaZerDude (C_BURKE) [#16]
 19 Apr 2007
To: Bill (ALBILLBERT2000) [#14] 19 Apr 2007

Thank you Bill, I will be calling you.........I can make the seals here as well.

It's a CPA...he does not need the paper, he fills the binder himself.....price will be a factor....and out in the middle of the ocean, well, it gets expensive......because of freight...

BUT, who know. I'll be calling you tomorrow. Thanks for the help


From: Bill (ALBILLBERT2000) [#17]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#16] 19 Apr 2007

Then if that is the case look into a pad printer or a used hot stamping machine

or cut gold foil using your laser for a decal.. I have even seen some companies just use View binders sold at any office supply house.. and put in a decorative ivory or fancy paper printed from a computer printer..

and yes view binders come with the binding side having a slip in opening


From: LaZerDude (C_BURKE) [#18]
 19 Apr 2007
To: Bill (ALBILLBERT2000) [#17] 19 Apr 2007

quote:
Then if that is the case look into a pad printer or a used hot stamping machine


The hot stamp won't work because of the rings... possibly a pad printer, but I know nothing about pad printing.......

I'll talk to you in the morning.....any particular time better than another?

From: Bill (ALBILLBERT2000) [#19]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#18] 19 Apr 2007

I am on the east coast.. I get in about 8 ish.. but anytime is good..

From: JHayes55 [#20]
 19 Apr 2007
To: LaZerDude (C_BURKE) [#18] 20 Apr 2007

quote:
How am I going to cut it? I'd have to have a sign company do it....


Dude - use laser foil instead of vinyl - that way you can do it in house on demand. Laser foil is just polyester instead of vinyl.

Show messages:  1-20  21-33

Back to thread list | Login

© 2024 Project Beehive Forum