Stunt Engraving: Can You Engrave a Putter?

From:	logojohn	8 Jul 2006
To:	Stunt Engraver (DGL)	7 of 15

4272.7 In reply to 4272.6
That is easy to compensate for. x = {q + [q2 + (r-p2)3]1/2}s1/3 + {q - [q2 + (r-p2)3]1/2}1/3 + p q = gram weight amount of fill used r= weight of material removed s= how high to step so you boots don't get full of it. .

From:	Harvey only (HARVEY-ONLY)	8 Jul 2006
To:	logojohn	8 of 15

4272.8 In reply to 4272.7
Darned messy shoes. There was no 's' in the equation. Philadelphia, PA (Really Bensalem) When you finally understand it completely... it changes.

From:	clay (CLAY_J1955)	8 Jul 2006
To:	Stunt Engraver (DGL)	10 of 15

4272.10 In reply to 4272.1
you didnt charge enough David.....LOL. A guy from Adams golf walks into the shop, i used to work at, says he needs a complete set of his new product line (TightLies) engraved for King Hussein of Jordan. The guy i worked for says he isnt interested but mabe since im a golfer he could make a deal with me. A long story short, I take 2 hours off the clock do the job, and a week later my new set of TightLies comes in from UPS.

From:	Stunt Engraver (DGL)	8 Jul 2006
To:	clay (CLAY_J1955)	11 of 15

4272.11 In reply to 4272.10
quote: you didnt charge enough David Clay, I agree. Of course, some people reading this thread, probably think I made a killing. The moral of the story is, while state-of-the-art, computerized engraving equipment, should be on everyone's wish list, there's still money to be made, at a fraction of the cost, with equipment that is probably collecting dust in many awards and engraving shops across the country. David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA
EDITED: 8 Jul 2006 by DGL

From:	Mike (MIKEN)	8 Jul 2006
To:	Stunt Engraver (DGL)	12 of 15

4272.12 In reply to 4272.11
David: I 'm sure you're right about a lot of equipment gathering dust. But How many could do that job as well as you. My bet is, not many. Mike Dist. of LAZER Cutting Grid St. Louis Laser, Inc. www.stl-laser.com

From:	Stunt Engraver (DGL)	8 Jul 2006
To:	Mike (MIKEN)	13 of 15

4272.13 In reply to 4272.12

Mike,

You're right. That's definitely an advanced procedure for pantograph engraving and not one I would recommend, to anyone without a lot of practice, in working without a standard means of depth control.

The fact remains, for someone looking to get their foot in the door, there's a lot of relatively inexpensive pantograph equipment out there.

Many jobs don't require "Stunt Engraving" and I like doing those too. :-)

David "The Stunt Engraver" Lavaneri
DGL Engraving
Port Hueneme, CA

EDITED: 8 Jul 2006 by DGL

From:	gt350ed	9 Jul 2006
To:	Harvey only (HARVEY-ONLY)	14 of 15

4272.14 In reply to 4272.8
Hey, dude! You start smokin again? Look again. There is, indeed, an "s" in the equation. B-) Ed Holley Victor Valley Trophy & Awards Co. and Coffee Mugs Online www.coffeemugsonline.com

From:	Harvey only (HARVEY-ONLY)	9 Jul 2006
To:	gt350ed	15 of 15

4272.15 In reply to 4272.14

It is so clogged that you cannot see the pile of 's' in the equation.

It surely cannot be that I am blind. :-$

Philadelphia, PA (Really Bensalem)

When you finally understand it completely... it changes.

Show messages: All 1-6 7-15

Adjust text size: Smaller 10 Larger

Beehive Forum 1.0.1 | FAQ | Docs | Support | Donate!