Remember...... - Engraving Etc. Forum

From:	Peter	2 Nov 2006
To:	LaZerDude (C_BURKE)	36 of 51

5208.36 In reply to 5208.34

we've had a massive misfunction with our themagulated hyper extender. As a result all our disticular arlanthiams have been burnt.

We now have to replace the particulant nano expander and re calibrate the thermolaterizer...otherwize it will just burn holes straight thru the metal...as we all know..

does everyone concur ?

Peter Vasic
Engraving Services Co.
Adelaide, Australia.
http://www.engravingservices.com.au

From:	LaZerDude (C_BURKE)	2 Nov 2006
To:	Peter	37 of 51

5208.37 In reply to 5208.36
quote: We now have to replace the particulant nano expander and re calibrate the thermolaterizer...otherwize it will just burn holes straight thru the metal...as we all know.. Peter, Whatever would you do without me.......I know that you know that I know that you know that you know that you must be EXTREMELY careful whe replacing the particulant nano expander, because if you do NOT take special note to know the correct pressure applied to the particulant, during recalibration, it is likely that it could become very parallent there by resulting in massive burns to the testiculant partition of the thermolaterizer its self, reducing the potency of the entire process. I KNOW that you know that I know that you know that. You DO know that don't you?

From:	Engravin' Dave (DATAKES)	2 Nov 2006
To:	LaZerDude (C_BURKE)	38 of 51

5208.38 In reply to 5208.37
Wear your safety goggles. :S

From:	Harvey only (HARVEY-ONLY)	3 Nov 2006
To:	Peter	40 of 51

5208.40 In reply to 5208.36
Told you that you should have collumated the particle beam. Now you are in a pile of burned brown stuff. Philadelphia, PA (Really Bensalem) When you finally understand it completely... it changes.

From:	Engravin' Dave (DATAKES)	3 Nov 2006
To:	LaZerDude (C_BURKE)	42 of 51

5208.42 In reply to 5208.41
Did you learn that from Peter?

From:	LaZerDude (C_BURKE)	3 Nov 2006
To:	Engravin' Dave (DATAKES)	43 of 51

5208.43 In reply to 5208.42

David,

Peter knows, that you know that I know that he knows that everying I know, you know that he knows that I learned from him. You know?

From:	Stunt Engraver (DGL)	3 Nov 2006
To:	Engravin' Dave (DATAKES)	45 of 51

5208.45 In reply to 5208.44
Beats Kemo Therapy. :-$ David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	Engravin' Dave (DATAKES)	3 Nov 2006
To:	Stunt Engraver (DGL)	46 of 51

5208.46 In reply to 5208.45
Does this thread still qualify to be under the General Discussion folder? Sheesh!
EDITED: 3 Nov 2006 by DATAKES

From:	Stunt Engraver (DGL)	3 Nov 2006
To:	Engravin' Dave (DATAKES)	47 of 51

5208.47 In reply to 5208.46
Presto changeo, it's in "Topic of Your Choice." David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	Engravin' Dave (DATAKES)	3 Nov 2006
To:	Stunt Engraver (DGL)	48 of 51

5208.48 In reply to 5208.47
Now we can really cut loose. Chuck will really be uninhibited now. :D

From:	Stunt Engraver (DGL)	3 Nov 2006
To:	Engravin' Dave (DATAKES)	49 of 51

5208.49 In reply to 5208.48
David, I thought the discussion was about as general as it could get, not that I was following too closely. :-) David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	LaZerDude (C_BURKE)	3 Nov 2006
To:	Stunt Engraver (DGL)	50 of 51

5208.50 In reply to 5208.49
quote: I thought the discussion was about as general as it could get, not that I was following too closely. :-) Generally speaking David, I find that speaking in generalities, generally, creates journalistic generalizations of a more general nature. You KNOW?

From:	Peter	3 Nov 2006
To:	LaZerDude (C_BURKE)	51 of 51

5208.51 In reply to 5208.37
quote: Peter, Whatever would you do without me....... Thats the point of this forum Chuck ! I might have a pretty good knowledge about particulant nano expanders....but its all the other knowledge ( all the in between really important stuff, that I gleen from you and the rest of the guys...that allows me to shine. This is the best forum ever... nanoo, nanoo ! :P :S B-) Peter Vasic Engraving Services Co. Adelaide, Australia. http://www.engravingservices.com.au
EDITED: 3 Nov 2006 by PETER

Show messages: 1-15 16-35 36-51

Adjust text size: Smaller 10 Larger

Beehive Forum 1.0.1 | FAQ | Docs | Support | Donate!