ARA Secaucus, NJ - Engraving Etc. Forum

From:	Bieb (HABIEB)	27 Jan 2006
To:	ALL	1 of 9

2828.1

I won't be able to make it to Vegas this year. :-( :'-(

But I am hoping to make it up to Secaucus, for the ARA show there March 30- April 1. Is anyone else going? I would like to get to meet some of the forum members there. If the Vegas crew does Forum Pins or some other EE identification, can you make them available for those attending Secaucus?

Thanks
Harold

www.southeastlaserengraving.com
Atlanta, Georgia

From:	Dee (DEENA-ONLY)	27 Jan 2006
To:	Bieb (HABIEB)	2 of 9

2828.2 In reply to 2828.1

Harold,
Our store is about 20 minutes from Secaucus so we will definitely be there. If you're driving up from Atlanta you will be driving right by us. We're four minutes off the NJ Turnpike. If you would like to stop by send us a pm and we'll coordinate.

Dee

Philadelphia, PA (Really Bensalem)

From:	Peter	27 Jan 2006
To:	Dee (DEENA-ONLY)	3 of 9

2828.3 In reply to 2828.2

Our stores are in Adelaide ! ;-) We'll...Think about swinging by !

regards
Peter

Peter Vasic
Engraving Services Co.
Adelaide, Australia.
http://www.engravingservices.com.au

From:	Dee (DEENA-ONLY)	28 Jan 2006
To:	Peter	4 of 9

2828.4 In reply to 2828.3

Isn't Adelaide next to Japip?

Seriously, what side of the road do Aussies drive on?

Dee

Philadelphia, PA (Really Bensalem)

From:	UncleSteve	29 Jan 2006
To:	Dee (DEENA-ONLY)	5 of 9

2828.5 In reply to 2828.4

http://en.wikipedia.org/wiki/Rules_of_the_road

And oddly enough there is no consistancy! The lefties are in red and the righties in blue..... except for a small part of Quebec where they flip the side for a few miles..... but then again it IS Quebec.... ;-)

"Genius ain't anything more than elegant common sense." Josh Billings

EDITED: 29 Jan 2006 by UNCLESTEVE

From:	Stunt Engraver (DGL)	30 Jan 2006
To:	Bieb (HABIEB)	6 of 9

2828.6 In reply to 2828.1
Harold, When you (and other EE members) get to the East Coast ARA show, go to the Epliog booth, where they'll be happy to hook you up with a very "stately" looking member badge. :-) David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	geebeau	1 Feb 2006
To:	ALL	7 of 9

2828.7

Sigh.. we were planning to go to Vegas, but will be at the Meadowlands instead. It's a smaller show, but it'll still be good to see some of the new stuff, hob nob with my fellow engravers, and get some new ideas.
Looking forward to seeing some of the folks from here as well.
The plan is to go there on Friday.

Steve
Custom ID & Awards

From:	JimK (JUSTTHE4OFUS)	9 Feb 2006
To:	ALL	8 of 9

2828.8 In reply to 2828.7

Vegas is definitely out of the question for me, besides at my age I couldn't stand all the scenery. At present, I am planning to come to the Secaucus show. Might be just me, might be the whole family. My boys love this stuff, and I encourage them as much as possible to be involved. They are 14 and will be my teen advisors for the next couple years. They have their own ideas for a whole line of ski bag tags (luggage tags) and jacket pulls, with photo and personal data for my new MPX-60. Once I get it setup I will let them run with their own ideas.

Jim

Jim Kenndy, Sr.
Just the 4 of Us Engraving
York, Maine
ULS 25W with rotary, MPX-60 impact
"Lost, but making good time."

"When nothing seems to help, I go and look at a stone-cutter, hammering away at his rock perhaps 100 times without as much as a crack showing. Yet at the 101st blow, it will split in two, and I know it was not that blow that did it, but all that had gone before." - Unknown

From:	Stunt Engraver (DGL)	9 Feb 2006
To:	JimK (JUSTTHE4OFUS)	9 of 9

2828.9 In reply to 2828.8
Jim, By all means, get your kids involved. Being introduced to the A&E industry, when I was 14, wouldn't have had as much impact on me. There was no computerized equipment. :-) David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA