I am here to help... - Engraving Etc. Forum

Advertising/Buy/Sell I am here to help...

Warning

Press Ctrl+Enter to quickly submit your post

Quick Reply

✏✏✏✏✏✏✏✏✏✏

Next

From:	Larry	24 Sep 2006
To:	ALL	1 of 6

4927.1
I would like to know what the most common problem is in holding items for the engraving process. I think I put this in the correct folder. Co-owner Engraving Fixtures Ltd. A very small company with large capabilities that does just what the name implies.

Previous

Next

From:	Stunt Engraver (DGL)	24 Sep 2006
To:	Larry	2 of 6

4927.2 In reply to 4927.1
Larry, This is the correct folder. Thank you. What type of engraving fixtures do you make? Laser or rotary/drag equipment, or both? David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

Previous

Next

From:	Larry	24 Sep 2006
To:	ALL	3 of 6

4927.3
Are you always this fast? Rotary most and we can do laser as well. We have a few items now and are adding more as the need and market develops. I don't know where to post pics and well, our website has some old stuff, www.engravingfixtures.com and we are in process of updating it. We can and will make specialty one-of's (they are usually not cheap). If you have an idea we will try and work with you on "almost" anything. Co-owner Engraving Fixtures Ltd. A very small company with large capabilities that does just what the name implies, in a creative and economical way.
EDITED: 24 Sep 2006 by LARRY

Previous

Next

From:	JHayes55	24 Sep 2006
To:	Larry	4 of 6

4927.4 In reply to 4927.3
Larry - Interesting web site - look like you can think outside the box from the design of some of your products. I am going to take a guess and say your a "clogger" :-)

Previous

Next

From:	Larry	24 Sep 2006
To:	ALL	5 of 6

4927.5
Actually the clogger is my partner in this venture. If I try to dance somebody will get hurt. Thanks for your kind words Co-owner Engraving Fixtures Ltd. A very small company with large capabilities that does just what the name implies, in a creative and economical way.

Previous

From:	logojohn	24 Sep 2006
To:	Larry	6 of 6

4927.6 In reply to 4927.1
I can rig a lot of things easily. The thing that I run across the most that takes extra time and aggravation are for things that do not have parallel sides such as a flat letter opener or blade of a knife. A basic flat jig like (left center of photo but maybe 3-5" long instead of the long one shown)those for holding plates would work a lot if they could be swiveled at one end similar to the new hermes knife holder like this or the attachment below. The thick holding area of theirs will often twist and let loose of thin items like blades and most often block the cutter from getting where it needs to be. It has oblong slots with a tightening nut on one end so you can close it at different angles. But I have not seen a basic plate jig like that. Sometimes a little thicker things would require some similar to the flat side of the new hermes watch jig.See attachment below. The silver peg holders can be used sometimes but often there is no place that the pegs fit that perfectly match the slant of the item. I assume you just want ideas for jigs and not a whole clamping system. I use the allgraphics vice (shown here with some blocks I added for clamping very thick items which might be another idea) or here and a new hermes vice from a pantograph clamped to the rotary table. Both accept standard jigs like newhermes makes. For the laser an economical slant riser would be nice. Such as to level an oblisque or crystal that is tapered thinner at the top. Their is one design available is about $800. Worth the money in the long run but hard to spend that much on $20 worth of metal when there are always other needs. It could accomplish the same thing but work in a different way to not ingringe on patents. Here is a way I commonly do it now. Underlined words have samples to view.

Adjust text size: Smaller 10 Larger

Beehive Forum 1.0.1 | FAQ | Docs | Support | Donate!

©2002 - 2024 Project Beehive Forum

Forum Stats