I wrote an article on that a long time ago, it is on my home computer, but I will try to remember. I have not done it in a few years.

The first thing to know is if there are tabs on the tile and it will be grouted.

If yes it is simple. Make your boxes the size of the tile including the tabs, it will then look right. You then group all of the boxes, (I think it is group not combine.) Then you powerclip to the group. Ungroup and you have the individual pieces.

If the tiles butt against each other you will need to make the boxes .2 inches larger, (12.2) to get that necessary .1 alignment frame. If you are really good and nothing moves you can go smaller, but why do that. You then overlap the boxes that .2, (.1 from each tile), and group. Powerclip and ungroup.

With the tabs you must throw away the image that would be in the grout for the final image to align correctly. Without the tabs you need the overlap to be duplicated on all the pieces to use for alignment.

This works in Corel Draw 9, never tested it in X3.

Philadelphia, PA (Really Bensalem)

When you finally understand it completely... it changes.

The only problem with that "leap of faith" is that it will mean that the untold hours I have spent over the last week trying to find the solution to the "problem" were a complete waste of time. Fortunately it was usually between 10pm and 2am that I was researching so I wasn't losing productive work time - just sleep time...

I really appreciate the experience you guys have and how you can explain to this newbie this "problem" is really not a problem.

THANKS to everyone!

I don't know about a better way, or what would work or not... But to answer the original question...

Make the image/page 36.2 x 36.2. Then make a 3x3 grid of 12x12 squares, lined up right on the edges (total dimensions of 36x36) centered on the page (I made them red for clarity). Then make nine 12.2 x 12.2 squares (I left them black). individually center each new square over an old red square.

The black squares now have an outer dimension of 36.2 and overlap each other black square by .2.

Take each black square and power clip-copy-paste into new CDR with a page size of 12.2 x 12.2 and print onto centered item.

CDR saved as Ver 9

EDIT... I think i misread, I made the overlap .1 on all sides, I guess change wherever I say .2 to .1 and you'll have a .05 overlap. Hopefully the concept still applies.

Shaddy

I found the article.
------------------------------------------
Making a Corel Template for Tile Murals
This is descended from the post of ARTGLASS crediting Tropical Graphics, crediting the original to Imprints, USA. Thank you all for this solid foundation to start from. It works in Corel 7 and 9. I have not tried it in any other version.

To make a template for tiles WITH overlapping edges to aid in alignment when subbing, use this procedure. Modify if you need loss of image for tiles with spacers.

Be sure that your image can be made to .2 inches larger than the final picture. (You will lose .1 inch from each edge.)

1) Open a new file in the normal size that you use.

2) With the box tool draw a box. Resize it to .2 inches longer and .2 inches higher than your tile to provide a .1 inch overlap on each edge.

3) Using the 'select' tool, click outside of the page. Set the duplicate X value to the horizontal size of the tile plus .1 inch and the duplicate Y value to 0.00.

4) Using 'ctrl+d' duplicate the number of tiles that you will use across.

5) Click outside of the page again. Set the duplicate X value to 0.00 and the duplicate Y value to the size of the tile plus .1 inch, remembering to make it a negative value. Now select all of the boxes and duplicate with 'ctrl+d' the number of tiles you will use downward.

6) Select all of the boxes and click on 'combine', Not group.

This gives you the template. Follow the instructions found at the Tropical Graphics website from here. When you separate the boxes there will be a duplicate edge on each tile containing a piece of the next tile image to help in aligning the image without losing the edge piece of image between tiles.

The Corel 7 print preview works a little differently than The Tropical Graphics instructions. To solve this problem put as many tiles on the page that will fit, then move toe others outside the borders of the page. Click 'layout' and 'insert pages' to add pages. When you go to the next page, anything outside of the original page will still show. Move what you need onto the page. You will now have a multi-page document that can be printed easily in a group or as single pages.

Thank you so much Dave & Lynn of Art Glass, Tropical Graphics, and Steve at Imprints, USA.

Philadelphia, PA (Really Bensalem)

When you finally understand it completely... it changes.

Gary, the pro's at making large format sublimation murals, such as Bison Coatings sister company, use large format printers and presses.

They print the image as one piece and then press with the tiles all placed next to each other, all at one time...

They don't worry about the grout lines, or small little spaces.

Remember, murals are going to be viewed from a distance, the space is not going to be noticed.

Now, we in the real world, using our small format printers and having to do the tiles individually, at .1" to our tile size to allow for easier placement onto the press.

Doug

Gee, I, as a member of the DSSI forum now feels little to no desire to answer any more of your questions.

Thanks.

Doug

Doug,
I really was kidding with that statement. I know that all of the forums I belong to have a lot of overlap with their members. I guarantee that a very large portion of EE, WOE, SMC, DSSI, etc., are the same people. We all share similar interests and the people who post a lot on one forum most likely post a lot on others as well. I can't tell you how many posts I see from the same people on all forums.

I hope you were kidding as well, I certainly didn't mean to offend anyone.

Gary

Actually, I got great replies from all forums. They each have their own merit and reflect on the person who gave the advice, not necessarily the forum.

After having been a member of the aforementioned forums for a few months, I can definately see that each of the forums have their own "personality" - this even though many people are members of all of the forums. EE was my "first" engraving forum, and you know what they say about your first. DSSI is my first Dye Sub forum also and I appreciate their focused expertise as well. There is nothing wrong with the others, but I usually start here and DSSI for my problem solving.