Shanks Alot! - Engraving Etc. Forum

From:	Stunt Engraver (DGL)	2 Jan 2007
To:	ALL	1 of 15

5644.1
Did you see Rodney's (inadvertent?) pun in the cutter grinder thread? Somehow, I knew he'd have an "angle." David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	MIKEY (JADEPUTTERS)	2 Jan 2007
To:	Stunt Engraver (DGL)	2 of 15

5644.2 In reply to 5644.1
and did you think he was a cut above any puns? Mikey www.pictureitinstone.com www.jadeputters.com "Both optimists and pessimists contribute to the society. The optimist invents the aeroplane, the pessimist the parachute."--- George Bernard Shaw

From:	Harvey only (HARVEY-ONLY)	2 Jan 2007
To:	MIKEY (JADEPUTTERS)	3 of 15

5644.3 In reply to 5644.2

I guess he just 'tipped' his hand.

Heard he needed a new truck, but instead he 'car buyed'.

When he imports materials he also has to use the right clearance angles.

Philadelphia, PA (Really Bensalem)

When you finally understand it completely... it changes.

From:	Dave Jones (DAVERJ)	2 Jan 2007
To:	Harvey only (HARVEY-ONLY)	4 of 15

5644.4 In reply to 5644.3
He's a 'sharp' guy. A real 'diamond' in the rough. ...Dave Dave Jones Design

From:	UncleSteve	2 Jan 2007
To:	Dave Jones (DAVERJ)	5 of 15

5644.5 In reply to 5644.4
Should have known you all would start dragging this out again! >.< You will all end up in your Grav o' plying your PUNishment on the rest of the world! :O) "Don't believe everything you think!"

From:	Stunt Engraver (DGL)	2 Jan 2007
To:	ALL	6 of 15

5644.6
Hey! I just "collet" as I see 'em. :-) David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	Dee (DEENA-ONLY)	3 Jan 2007
To:	Harvey only (HARVEY-ONLY)	7 of 15

5644.7 In reply to 5644.3

I think y'all need to "burnish" this thread.

Dee

Philadelphia, PA (Really Bensalem)

From:	Stunt Engraver (DGL)	3 Jan 2007
To:	Dee (DEENA-ONLY)	8 of 15

5644.8 In reply to 5644.7
Leave it to Dee to give us the "shaft." David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	Dave Jones (DAVERJ)	3 Jan 2007
To:	Stunt Engraver (DGL)	9 of 15

5644.9 In reply to 5644.8
That's because she's by the sea on the east and you're by the sea on the west. And there's a lot of distance between the "sea and sea". ...Dave Dave Jones Design

From:	UncleSteve	3 Jan 2007
To:	Dave Jones (DAVERJ)	10 of 15

5644.10 In reply to 5644.9
Have you gauged the depth of that statement? Just right to "cap" off the thread. "Don't believe everything you think!"

From:	Dave Jones (DAVERJ)	3 Jan 2007
To:	UncleSteve	11 of 15

5644.11 In reply to 5644.10
Whenever I come into this thread I feel like I'm on the 'nosecone' of a rocket ready to take off. ...Dave Dave Jones Design

From:	Stunt Engraver (DGL)	3 Jan 2007
To:	ALL	12 of 15

5644.12
You guys are forcing me to "grind" out some of my worst puns. And that's saying a lot. :-) David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

From:	LaZerDude (C_BURKE)	3 Jan 2007
To:	ALL	13 of 15

5644.13
Could we "collet" quits "andjust table" this?

From:	Harvey only (HARVEY-ONLY)	3 Jan 2007
To:	LaZerDude (C_BURKE)	14 of 15

5644.14 In reply to 5644.13
Although I like to be on the cutting edge, this thread is becoming quite a grind. Philadelphia, PA (Really Bensalem) When you finally understand it completely... it changes.

From:	Stunt Engraver (DGL)	3 Jan 2007
To:	Harvey only (HARVEY-ONLY)	15 of 15

5644.15 In reply to 5644.14
Harvey, That goes without saying. You don't "halve" to say it out loud. David "The Stunt Engraver" Lavaneri DGL Engraving Port Hueneme, CA

Adjust text size: Smaller 10 Larger

Beehive Forum 1.0.1 | FAQ | Docs | Support | Donate!